在生產過程中會遇到一個頭疼的問題，就是紙箱的坍塌和粘膠箱機不牢固的問題，總結出的解決辦法就是提高紙板的材質，提高抗壓強度和防潮性能，從而降坍塌率。另外，工廠需要提高粘接強度，增加淀粉糊的固含量，通過減少膠水的用量來提高紙板的硬度，解決了粘盒機的問題。
In the process of production, there will be a headache, that is, the collapse of the carton and the unsteadiness of the viscose box machine. The solution summed up is to improve the material quality of the cardboard, improve the compressive strength and moisture-proof performance, so as to reduce the collapse rate. In addition, the factory needs to improve the bonding strength, increase the solid content of starch paste, improve the hardness of cardboard by reducing the amount of glue, and solve the problem of box gluing machine.
包裝廠如何處理粘盒機不牢固盒坍塌的問題生產使用時應注意以下幾點:
How to deal with the collapse of the loose box of the box gluing machine in the packaging factory should pay attention to the following points in production and use:
1、控制生紙的使用
1. Control the use of raw paper
檢查瓦楞紙的施膠狀況、原紙表面吸水指數的效能。如果原始紙張的表面施膠差,吸水會偏高,而且很容易受溫冷藏和潮濕環境,導致的水分,軟化并減少完成的抗壓強度。
Check the sizing condition of corrugated paper and the efficiency of water absorption index of base paper surface. If the surface sizing of the original paper is poor, the water absorption will be high, and it is easy to suffer from low temperature cold storage and humid environment, resulting in moisture, softening and reducing the finished compressive strength.
2、生產紙板要控制紙板的含水量
2. To control the moisture content of paperboard in production
紙板的含水率不能太多，因為含水率是紙板硬度，影響紙板的邊壓指數。在紙板加工過程中，單面機和雙面機的上膠量不能太大。一旦膠水量大，紙板的形狀就會變形，而瓦楞紙板的形狀則直接影響紙板的邊壓、邊壓，抗壓強度也會降。
The moisture content of the paperboard can not be too much, because the moisture content is the low hardness of the paperboard, which affects the edge pressure index of the paperboard. In the process of cardboard processing, the amount of glue on single-sided machine and double-sided machine should not be too large. Once the amount of glue is large, the shape of paperboard will be deformed, while the shape of corrugated paperboard will directly affect the side pressure and side pressure of paperboard, and the compressive strength will also be reduced.
3、板材的粘接強度要大
3. The bonding strength of the plate should be large
粘接強度是瓦楞紙與襯紙、面紙的粘接力。如果紙板假粘著、受壓，表面的紙張或紙張會與瓦楞紙分離，那么抗壓強度就會直線下降。4. 生產過程中的間隙壓力控制要適度
The adhesive strength is the adhesive force between corrugated paper, liner paper and surface paper. If the paperboard is stuck and pressed, the surface paper or paper will be separated from the corrugated paper, then the compressive strength will drop in a straight line. 4. The gap pressure control in the production process should be moderate
特別要注意的是，糊盒機的糊料間隙壓力不能太小，雙面機、模切機的太陽輪的間隙壓力要控制在合理的范圍內，以避免瓦楞坍塌，影響紙板的抗壓強度。
In particular, the paste gap pressure of the pasting machine should not be too small, and the gap pressure of the sun wheel of the double-sided machine and the die-cutting machine should be controlled within a reasonable range to avoid the corrugation collapse and affect the compressive strength of the cardboard.
5、采用噴淋劑、防水輕油等表面解決防水防潮問題
5. Using spray agent, waterproof light oil and other surfaces to solve the problem of waterproof and moisture-proof
